ASTM A179/ASME SA179 U Bend (U Bent) Heat Exchanger Tubes

Short Description:

ASTM A179/ASME SA179 U Bend (U Bent) Heat Exchanger Tubes Mainly used in Heat Exchanger and Boiler.Wall thickness(WT): 1.65 mm——2.77 mm.Outer diameter (OD): 19.05mm - 38.1mm

Product Detail

Product Tags

ASTM A179/ASME SA179 U Bend (U Bent)  Heat Exchanger Tubes
ASTM A179/ASME SA179 U Bend (U Bent) Heat Exchanger Tubes Mainly used in Heat Exchanger and Boiler.
 
ASTM A179/ASME SA179 U Bend Heat Exchanger Tubes Quick Details
Manufacture:Seamless process ,cold drawn.
Bending Details: According to Bending Drawings.
Wall thickness(WT): 1.65 mm——2.77 mm.
Outer diameter (OD): 19.05mm - 38.1mm
Length: 6M or specified length as required, the longest is 26 meters.
Ends: Plain End
 
Additional Info
Port of Shipment: Tianjin, China
Payment Terms:T/T, LC
Delivery: 7-15 days after payment
Surface: Tubes will be varnished to prevent rust.
Marking: Standard + Steel Grade + Size + Heat No + Lot No
Package: Wooden Boxes,Crates (steel/wooden) or as required
 


Chemical Composition of ASTM A179/ASME SA179 U Bend (U Bent)  Heat Exchanger Tubes

Material Chemical Composition(%)
C Si Mn P S
STM A179/ASME SA179  0.06-0.18 ≤ 0.25 0.27-0.63 ≤0.035 ≤0.035
 

Mechanical Propertie of ASTM A179/ASME SA179 U Bend (U Bent)  Heat Exchanger Tubes

Grade ASTM A179
Tensile Strength(MPa) ≥325
Yield Strength(MPa) ≥180
Elongation,% ≥35
Hardness, HRB ≤72



 
Specifications of ASTM A179/ASME SA179 U Bend Heat Exchanger Tubes
 
Bending Details: Can Accord to Bending Drawings.
 
  



Technical Parameters
Outer diameter: 12.7-38 mm
The bending radius is from 1.5 times the outer diameter to 1250 mm. The outer diameter is over 28mm,
The minimum bend radius can be further discussed.
Straight pipe length is the shortest 1000mm
Straight pipe length up to 12000mm
The bending radius is below 1000mm and heat treatment is required.
 
Bent pipe technology standard
Technical Standard 7-2-1179
DIN 2879, TEMA RCB 2.31
Can be specified according to customer requirements. Can also follow some general techniques
Specifications.
 
 
Heat treatment
If requested by the customer, we add a straight pipe section with a minimum of 150mm according to the elbow.
Heat treatment is performed.
The computer controls the heat treatment furnace and records all the data.
The tube is filled with a protective gas - argon.
 
Annealing Status:

Annealing
Solution annealing Stress relief annealing Stabilized annealing

 
Hydrostatictest
All U-tubes are subjected to a hydrostatic test after heat treatment.
The test time is not less than 5 seconds at the set pressure.
All tubes were blown dry and carefully cleaned after the test.

Measuring, cutting, deburring, cleaning
Accurately measure U-tubes according to relevant standards or customer requirements.
All pipes should be cut to length, deburred, and air dried to the inner wall.
Seal the ends with a plastic cap before packing.
 

Package
Use a strong, and depending on the distance to the destination, choose an open or sealed wooden case with a maximum weight of 8,000kg.
Both ends of the pipe are sealed with a plastic cap
Each elbow radius specification is vertically separated
Each row is separated by a chlorine-free plastic sheet every two meters
Each bundle of tubes is wrapped in plastic sheet
Customers can provide packaging drawings or Sandvik ready to package
The packing list should be packed in a plastic bag and placed in a wooden box for detailed review at the time of arrival - including all bend radii and pipe lengths.
 
 
Packaging picture of ASTM A179/ASME SA179 U Bend Heat Exchanger Tubes




Products categories

  • field:title/]

    ASTM A179 ASME SA179 Finned Tub

  • field:title/]

    ASTM A179/ASME SA179 U Bend (U

  • field:title/]

    ASTM A179 ASME SA179 Seamless H